529, "The OS you selected is not compatible with the partition(s) on the current boot drive. MaxBlast 3 can partition and format your new drive with the FAT file system but no files can be copied from this version on MaxBlast 3 It is recommended that you use MaxBlast 3 for Windows to setup your new drive...Do you wish to Continue?"
530, "Locate the jumper block on the rear of your drive in between the ATA connector and power connector. Note the jumper settings printed on the label on the top of the drive. A custom manual will be created at the end of this tutorial that will indicate whether you need to jumper your drive as Master, Slave, or Cable Select. Click \"Help\" for more information on how to change the jumper settings on your drive."
531, "A jumper is a small plastic piece that slides over a pair of configuration pins. For PATA and SCSI drives an important step in the installation process is to set the jumpers on the back of your hard drive so your system can identify it.\n\nThe following definitions describe the jumper settings:\n\nMaster: This setting can be used if you will be using the new hard drive as a primary master boot drive or a secondary master additional storage drive. The hard drive should be connected to the black connnector at the end of the ATA cable.\n\n"
532, "Slave: The setting can be used if you will be using the new hard drive for additional storage only and is not typically used for boot devices on a Windows-based system. The hard drive should be connnected to the gray (middle) connector on the ATA cable.\n\nCable Select: This setting is an alternate method of hard drive identification that can be used instead of the master and slave settings. With cable select enabled, all hard drives positioned on the black (master) connector of the ATA cable will identify as master, and all hard drives positioned on the gray (middle) connector will identify as slave.\n\n"
533, "Setting the Jumpers"
534, "Backup / Restore MBR"
535, "Blank"
536, "You can access all Disk Manager controls using only the keyboard.\n\nUse the Tab key to switch between controls, ie buttons, check boxes, list boxes, tab controls.\n\nUse the arrow keys to select items in a list or to switch between tabs in a tab control.\n\nItems in a list can be selected using the spacebar/enter keys.\n\nYou can quickly select certain controls by using a hot key. This is done by pressing the Alt key followed by a letter. The letter assigned to a selection will be underlined in that item's description. Alt-N and Alt-B are assigned to the 'Next' and 'Back' buttons."
537, "Keyboard Navigation"
538, "For the latest support information, please visit the Maxtor Knowledge Base at http://www.maxtorkb.com.\n\nNorth America\n\nE-mail Support:\twww.maxtor.com\nPhone Support:\t1-800-2-MAXTOR (1-800-262-9867) \nOutside the US:\t(303)-678-2015\nPhone Hours:\t\tM-F 6am - 6pm (Mountain Time)\nFax Support: \t\t(303) 678-2260\n\nEurope\n\nTechnical Support is available in English, French and German.\n\nE-mail Support:\t\t\twww.maxtor.com\nPhone Support (All countries):\t+353 1 204 1111\nIn France:\t\t\t\t08 25 31 43 22\nIn Germany:\t\t\t\t01801 62 98 67\nPhone Hours:\t\t\t\tM-Th 8.30am - 5pm (GMT) \nF 8.30am - 4pm (GMT) \nFax Support:\t\t\t\t+353 1 286 1419\nMaxFax (FaxBack server): \t\t+353 1 204 1122\n\nAustralia\n\nE-mail Support:\t\t\twww.maxtor.com\nPhone Support:\t\t\t+61-2-9369-3662\nFax Support:\t\t\t\t+61-2-9369-2082\nMaxFax (FaxBack server):\t\t+61-2-9369-4733\n"
539, "Contacting Maxtor"
540, "Please eject the MaxBlast CD and/or floppy and press Ctrl-Alt-Delete to reboot."
541, "File Copying Errors"
542, "If an error occurs copying files to a drive, run ScanDisk and Defrag on the source drive and try again."
543, "Please refer to the \"File Copying Errors\" section of help for more information."
